Skip to content
AdCol PolyPlast
Twin-screw masterbatch compounding line

Supplying converters across India

Masterbatch Manufacturer in India

AdCol PolyPlast is a masterbatch company in India, with its office and works in Rajkot, Gujarat. We make color, white, black and additive masterbatches and CaCO₃ filler compounds for blown film, pipe, moulding and raffia, each standard grade backed by a published one-page TDS and per-grade compliance declarations.

Installed annual extrusion capacity
10,000 MT
Custom color lab plaques
48 h
Delta-E shade tolerance
< 0.5

Why AdCol

What to expect from a masterbatch manufacturer in India

AdCol PolyPlast LLP is a masterbatch manufacturer in India, compounding color, white, black and additive masterbatches and CaCO₃ filler compounds at its works in Rajkot, Gujarat. The plant runs high-torque co-rotating twin-screw extrusion with 10,000 MT of installed annual capacity. Film, pipe, moulding and raffia grades come off the same lines. Four standard grades carry a published one-page technical data sheet, and custom colors are matched to your RAL, Pantone or part reference.

When you compare masterbatch manufacturers in India, the numbers worth weighing are the ones you can check: active loading, MFI, filter pressure value, dispersion rating and Delta-E. FPV tells you how quickly a concentrate will load your screen pack. MFI tells you whether it will mix into your resin at the let-down you plan. AdCol prints each value with its test method and tolerance, so your QC lab can check incoming material the same way. Below: what we make, how supply works, how quality is proven, and the route from enquiry to production order. For a wider checklist, read our guide on how to choose a masterbatch supplier.

Products

Five product families from one masterbatch manufacturer in India

Each family has a representative grade. Four have a published one-page TDS; custom colors are specified per shade. Figures below are typical values. See every grade in Products.

  • RAL / Pantone

    Color Masterbatches

    MB-CLR-CUSTOM is matched to your RAL code, Pantone reference or a physical part. Pigments are chosen for your heat history, with stability from 240°C – 300°C, and every shade is approved by spectrophotometer at Delta-E < 0.5.

    Pigment System
    Organic / Inorganic
    Delta-E Tolerance
    < 0.5
    Heat Stability
    240°C – 300°C
    MB-CLR-CUSTOM grade details
  • Up to 70% rutile

    White Masterbatches

    MB-W70-PE carries 70% chloride-process rutile TiO₂ with an organic surface coating in an LLDPE/LDPE carrier. Moisture of 0.12% or less and FPV below 0.8 bar/g keep fast blown film bubbles clean of lacing. Start at 1.5% – 3.5% in packaging film.

    Active TiO₂
    70%
    Specific Gravity
    2.05
    MFI
    12.0 g/10 min
    MB-W70-PE grade details
  • Agri & Pipe

    Black Masterbatches

    MB-BLK40-AG holds 40% furnace carbon black with a 20 nm primary particle size, rated ≤ 2 for dispersion per ISO 18553. At 5.0% – 6.25% it puts 2.0% – 2.5% carbon black into drip laterals to IS 12786 / ISO 4427.

    Carbon Black
    40%
    Particle Size
    20 nm
    Dispersion
    ≤ 2 (ISO 18553)
    MB-BLK40-AG grade details
  • PPA / UV / Slip

    Additive Masterbatches

    MB-ADD-SAB pairs 5.0% erucamide slip with 10.0% micronized silica anti-block in virgin LLDPE. Kinetic COF drops below 0.20 after 24 hours, with under 2% haze. PPA, UV stabilizer and antioxidant packs are formulated to order.

    Actives
    Erucamide / Natural Silica
    Film COF
    < 0.20
    Haze Impact
    < 2%
    MB-ADD-SAB grade details
  • CaCO₃ / Talc

    Calcium & Filler Compounds

    CP-CA80-PE loads 80% stearic-coated CaCO₃ at a 1.5 μm average particle size, with a top cut of 6 μm or less. Addition levels run 15% – 45% in HDPE shopping and garbage bags and 3% – 12% in PP raffia tapes.

    CaCO₃ Content
    80%
    Particle Size (D50)
    1.5 μm
    Coating
    Stearic acid
    CP-CA80-PE grade details
  • Before you order

    Read the data sheet first

    Every standard grade has a one-page TDS with typical values, test methods and let-down ratios, so you can compare like with like.

    TDS Library

How supply works

How a converter anywhere in India buys from AdCol

What a masterbatch supplier in India should give you before the first order: a named plant, published data, a trial on your line, packing that keeps moisture out, and audit documents.

  • Made and tested in Rajkot

    Every grade is compounded and tested at our works in Rajkot, Gujarat, on high-torque co-rotating twin-screw lines with 10,000 MT of installed annual capacity. A converter in any state buys against the same test methods and the same published values.

  • A published TDS before you buy

    Each standard grade has a one-page technical data sheet listing typical values, test methods, tolerances, let-down ratios, compliance and packaging. Compare MB-W70-PE or CP-CA80-PE line by line with the grade you run today, in the TDS library, before you ask for a sample.

  • Lab plaques, then trial lots

    For a custom color, the lab extrudes a plaque in 48 hours and measures it by spectrophotometer. Once you approve the plaque, a trial lot follows for your own line, so the bulk order rests on results from your extruder, not ours.

  • Packed for the material

    Every grade ships in 25 kg units on pallets, in a bag chosen for what is inside: multi-wall kraft moisture-barrier bags for white, UV-stabilized laminated PP woven bags for black, PE-lined kraft paper for additives and lined PP woven sacks for CaCO₃.

  • Documents for your audit

    MSDS, RoHS, REACH and food-contact declarations are issued per grade on request from the MSDS and regulatory desk. MB-W70-PE, MB-ADD-SAB and CP-CA80-PE are declared to FDA 21 CFR 177.1520; MB-W70-PE also meets EU 10/2011.

  • Phone, WhatsApp and email support

    Call or WhatsApp +91 90544 82828, or write to adcolindia@gmail.com. Enquiries are routed to the lab and sales desk, so dosing, grade selection and line-trial questions reach the people who test the grade. Contact details and directions are on one page.

Quality control

How quality is proven, lot by lot

When you shortlist plastic masterbatch manufacturers in India, ask which method sits behind each number. At AdCol, every production lot is screened against ASTM and ISO parameters for melt flow, active loading and dispersion before it is cleared for dispatch. The four checks below predict how a grade will behave on your extruder. The full method table, from density to haze, is on the quality control page.

Compliance statements refer to the masterbatch as supplied. The finished article still depends on your full formulation, process and end use.

  • Melt flow index

    Measured to ASTM D1238 / ISO 1133 at 190°C under 2.16 kg, and 21.6 kg for pipe grades. MB-W70-PE reads 12.0 g/10 min ± 3.0, a guide to how cleanly it lets down into your resin.

  • Filter pressure and dispersion

    EN 13900-5 forces melt through a 14 μm screen: MB-W70-PE stays below 0.8 bar/g and MB-BLK40-AG below 1.0 bar/g. ISO 18553 microtome rating and DIN 53770 mesh retention at 45 μm cover black and filler.

  • Spectrophotometric color

    Shades are approved by instrument to Delta-E < 0.5 against your standard, not by eye. The same measurement checks the whiteness index of CP-CA80-PE, specified at 95.0 or higher.

  • Regulatory frameworks

    MB-W70-PE, MB-BLK40-AG and MB-ADD-SAB are declared to RoHS 2011/65/EU and REACH SVHC. Three grades meet FDA 21 CFR 177.1520 for food contact, plus 178.3860 for MB-ADD-SAB and EU 10/2011 for MB-W70-PE. See the compliance matrix.

Next steps

From first enquiry to production order

  1. 01

    Share polymer, process and target

    Send your base polymer, end process, target let-down ratio and any RAL or Pantone code through the Request Sample form, by WhatsApp on +91 90544 82828 or by email.

  2. 02

    Lab review and grade confirmation

    The lab checks your polymer, process and let-down against the TDS ranges, then confirms a standard grade or proposes a formulation for a custom brief. The selection guide shows the same starting points.

  3. 03

    Plaque or sample for approval

    Custom colors get a lab plaque in 48 hours, measured to Delta-E < 0.5. Standard grades are sampled against their published TDS so you can compare like with like.

  4. 04

    Trial lot on your line

    After approval, a trial lot ships from Rajkot for a run on your own extruder, die and resin. The TDS itself advises converters to run internal extrusion trials before relying on typical values.

  5. 05

    Production order and documents

    Once the trial passes, the production order is quoted and packed in 25 kg units on pallets, with the MSDS and the declarations your audit needs issued per grade.

FAQ

Questions buyers ask before they order.

  • How do I choose a masterbatch manufacturer in India?

    Ask for four things before you order: a published TDS with test methods and tolerances, a sample or trial lot to run on your own line, compliance declarations issued per grade, and a named plant. AdCol PolyPlast publishes a one-page TDS for each standard grade, compounds every grade at its works in Rajkot, Gujarat, and issues MSDS, RoHS, REACH and food-contact declarations on request.

  • Is it masterbatch or master batch?

    Both spellings describe the same product: a concentrate of pigment, filler or additive dispersed in a carrier resin and cut into pellets. A buyer searching for a master batch manufacturer in India is looking for the same thing as one who writes it as a single word. AdCol PolyPlast uses the one-word form, masterbatch, on its TDS and website.

  • Where is AdCol's plant, and does it supply outside Gujarat?

    AdCol PolyPlast compounds every grade at its office and works at Fortune 5, Sardarnagar West 1, Nr. Astron Underbridge, Rajkot, Gujarat 360001. Installed annual extrusion capacity is 10,000 MT. Grades are supplied to converters across India from Rajkot, packed in 25 kg units on pallets, and prospective customers can plan a visit to the works.

  • What is a let-down ratio and how is it calculated?

    Let-down ratio is the percentage of masterbatch blended into natural resin. To reach a target, divide the active content you need by the active content of the masterbatch. For 2.5% carbon black from AdCol MB-BLK40-AG, which carries 40% carbon black, the working is 2.5 ÷ 40 = 6.25% let-down. Each AdCol TDS lists starting ranges by application.

  • Which documents does AdCol provide for a grade?

    Each AdCol standard grade has a one-page technical data sheet covering typical properties, test methods, tolerances, let-down ratios, compliance and packaging. A TDS describes how the product performs; an MSDS covers safe handling, storage and hazards. AdCol issues the MSDS plus RoHS, REACH and food-contact declarations per grade on request, so procurement and QC teams can file them for audits.

  • Are AdCol masterbatches food-contact compliant?

    Three AdCol standard grades are declared to US FDA 21 CFR 177.1520: MB-W70-PE white, MB-ADD-SAB slip and anti-block, and CP-CA80-PE filler. MB-W70-PE also meets EU 10/2011, and MB-ADD-SAB is approved under FDA 21 CFR 178.3860. Custom colors can be specified as food-contact compliant at the briefing stage. Compliance of the finished article depends on the converter's full formulation and end use.

  • How does AdCol match and approve a custom color?

    Send a RAL or Pantone code, a reference part or a physical sample, with your base polymer, process and wall thickness. The AdCol lab tunes carrier and melt flow to your resin, then extrudes a lab plaque in 48 hours. The plaque is measured by spectrophotometer and must read Delta-E < 0.5 against your standard. A trial lot follows your approval.

  • How do I get a price or a sample from AdCol?

    Use the Request Sample form on adcol.in, call or WhatsApp +91 90544 82828, or email adcolindia@gmail.com with your base polymer, end process, target let-down ratio and expected volume. AdCol quotes on enquiry rather than publishing a price list. Custom colors are quoted per shade, carrier and end use, because the pigments and their loading set the cost.

Start a trial

Tell us your resin, process and target let-down

Our lab confirms the grade and sends a sample or lab plaque for approval. Call or WhatsApp +91 90544 82828, or email adcolindia@gmail.com.