Skip to content
AdCol PolyPlast

Buyer's Guide

How to Choose a Masterbatch Supplier: A 12-Point Checklist

Two masterbatch quotes can look identical on paper and run very differently on your line. The gap shows up later as specks, extra screen changes, shade drift and missing paperwork at audit time. Here is how to choose a masterbatch supplier: 12 questions to put to every shortlisted vendor, and the answers that should satisfy you.

By AdCol PolyPlast · Updated · 10 min read

Key takeaways

  • Get carrier, MFI and heat stability in writing. A grade that suits your resin and melt temperature lets down without streaks or gels.
  • Judge dispersion by numbers: FPV in bar/g to EN 13900-5, or an ISO 18553 microtome rating for black.
  • Color approval should be instrumental, with a stated Delta-E limit, not a visual check.
  • Every grade needs a TDS with test methods and tolerances, an MSDS, and grade-specific food-contact, RoHS and REACH declarations.
  • Run a trial lot on your own line before bulk orders, and agree the documents that travel with every dispatch.

The 12-point masterbatch supplier checklist

Send these 12 questions to every shortlisted supplier in the same words, and ask for written answers. Anything vaguer than the right-hand column needs a follow-up call.

CheckWhy it mattersWhat a good answer looks like
1. Carrier compatibilityA mismatched carrier mixes poorly and causes streaksCarrier named on the TDS and matched to your base polymer
2. Melt flow indexAn MFI far from your resin's disperses unevenlyMFI with test conditions, e.g. 190°C / 2.16 kg, and a tolerance
3. Let-down ratioDosage sets your real cost per kg of productActive content plus an LDR range for your application
4. Heat stabilityPigments and additives degrade above their limitA temperature and dwell time, tested to a named method
5. DispersionAgglomerates block screens and cause specksFPV in bar/g at 14 μm, or a microtome rating
6. Color toleranceShade drift between lots shows on the shelfSpectrophotometer approval with a numeric Delta-E limit
7. Lab and test methodsClaims without methods cannot be comparedIn-house MFI, dispersion and color tests to ASTM, ISO, EN or DIN
8. TDS and MSDSQC and safety teams need both before useOne TDS and one MSDS per grade, with revision numbers
9. Food contact, RoHS, REACHBrand owners and auditors ask for proofDeclarations per grade that name the regulation
10. Capacity and packagingShort supply or damp pellets stop linesStated installed capacity; moisture-barrier bags suited to the grade
11. Trial lots and lot documentsA lab plaque does not prove line behaviourTrial lot before bulk; lot number and test report with each dispatch
12. Shade matching and line supportProblems surface on your line, not in the labMatching to RAL, Pantone or a part, plus help during trials
Masterbatch supplier checklist

Technical fit: carrier, MFI, let-down ratio and heat stability

Start with the resin you run. The carrier polymer has to melt and mix with your base polymer at your temperatures, or pigment quality will not save the run.

  • Carrier (check 1). LLDPE, LDPE and HDPE carriers suit polyethylene film and pipe; PP carriers suit raffia and PP moulding. A universal carrier spans several polymers but can affect mechanical properties at high dosing.
  • MFI (check 2). Melt flow index shows how easily the masterbatch flows. A value close to, or slightly above, your resin's usually mixes well. Insist on test conditions: 190°C / 2.16 kg for polyethylene, often 21.6 kg as well for pipe grades.
  • Let-down ratio (check 3). Compare quotes on cost per kg of finished product. A cheaper grade dosed at 4% can cost more than a dearer one at 2.5%. Ask for the active content and the LDR range for your application.
  • Heat stability (check 4). Ask for a temperature, a dwell time and the method, for example DIN 53772, and compare it with your real melt temperature plus a margin for long residence. Slip additives such as erucamide are more heat-sensitive than most pigments.

Try several dosages against your batch size in the let-down ratio calculator.

Proof of quality: dispersion, Delta-E and lab methods

Every supplier calls its dispersion excellent. Ask for numbers tied to a published test method.

  • Dispersion (check 5). The filter pressure value (FPV, EN 13900-5) measures how much pressure builds as melt passes a fine screen, in bar/g; lower means fewer agglomerates. Carbon black is usually rated by ISO 18553 microtome, fillers by residue on a 45 μm mesh (DIN 53770). Ask which limit each lot is released against.
  • Color tolerance (check 6). Delta-E is the measured color difference between your standard and the sample. Near 1.0, most observers struggle to see it; tight matches are often set at 0.5. Agree the limit, the formula (CIELAB or CIEDE2000), the light source and whether readings are on a plaque or your part.
  • Lab and methods (check 7). In-house MFI, dispersion and spectrophotometer equipment lets each lot be tested before it leaves. See the lab on a works visit. Compare how AdCol's lab screens each lot.

One trap: typical TDS values are not release limits. Ask which properties are checked on every lot, and what happens to a lot that fails.

Documents and compliance: TDS, MSDS, food contact, RoHS and REACH

Paperwork shows a supplier's discipline. A vague spec sheet usually means loose control on the line.

  • TDS (check 8). Each property should carry a test method, unit, typical value and tolerance, plus let-down ranges, compatible resins, packaging and storage. Check the revision number and date.
  • MSDS (check 8). The material safety data sheet covers hazards, handling, storage, fire fighting and disposal. Stores and safety teams need it before the first bag arrives.
  • Food contact (check 9). For food packaging, ask for a declaration naming the regulation, such as US FDA 21 CFR 177.1520 for olefin polymers or EU 10/2011 for plastic food-contact materials. A 'food grade' label is not a declaration.
  • RoHS and REACH (check 9). RoHS 2011/65/EU caps lead, mercury, cadmium, hexavalent chromium, PBB, PBDE and, since 2015/863, four phthalates. For REACH, ask for an SVHC statement against the current Candidate List. Exporters need both.

A declaration covers only the masterbatch as delivered; the finished article also depends on your recipe, process and end use. The AdCol compliance matrix shows one per-grade layout.

Supply: capacity, packaging, trial lots and dispatch documents

A good grade is only useful if it arrives on time, dry and identical to the one you approved.

  • Capacity (check 10). Ask for installed annual capacity and how much is committed. A supplier running near full can push your order back at peak demand.
  • Packaging (check 10). Damp pellets cause voids and streaks in thin film, and carbon black is especially hygroscopic. Look for moisture-barrier bags, palletised loads and a stated shelf life.
  • Trial lots (check 11). A plaque proves the shade; only a trial lot on your own line proves output, screen life and dosing. Ask for one before the first bulk order.
  • Documents with each dispatch (check 11). Agree what travels with every lot: a lot number on each bag, a certificate of analysis (COA) with tested values, and an invoice naming the approved grade. Without them, a complaint cannot be traced to a lot or its test results.

Service: shade matching, technical support and line trials

When a bubble keeps breaking on the night shift, the supplier's lab matters more than its brochure.

  • Shade matching (check 12). Ask which references they accept (RAL, Pantone, a physical part), how long a lab match takes and how many correction rounds are included.
  • Technical support (check 12). A useful supplier asks about your polymer, process, gauge and target LDR before recommending anything. Find out who answers process questions, and how fast.
  • Line trials (check 12). For a new grade or supplier, ask whether their team will help set dosing and temperatures on the first run, and what happens if the trial fails.

Score each supplier 0–2 per check: no answer, partial, documented. Below 18 out of 24 calls for a second conversation before a purchase order.

Red flags in a masterbatch quote

  • No TDS, or a TDS with values but no test methods or tolerances.
  • Dispersion described in adjectives, with no FPV, microtome or mesh result.
  • Color approved by eye, with no Delta-E figure.
  • Food-contact claims without a declaration naming the regulation.
  • No MSDS or trial lot until after a purchase order.
  • A price per kg with no active content or recommended LDR.
  • Bulk material that differs from the approved trial, with no explanation.

How AdCol answers the checklist

AdCol PolyPlast is a masterbatch manufacturer in India with its office and works in Rajkot, Gujarat. The answers below come from its published TDS and site pages.

  • Technical fit: virgin LLDPE, HDPE and PP carriers; MFI stated with test load, such as 12.0 g/10 min at 190°C / 2.16 kg for MB-W70-PE; heat stability of 260°C – 300°C across the standard grades.
  • Let-down: an LDR range per application on every TDS, for example 5.0% – 6.25% for drip laterals with MB-BLK40-AG.
  • Dispersion: FPV < 0.8 bar/g on MB-W70-PE and < 1.0 bar/g on MB-BLK40-AG, ISO 18553 rating ≤ 2 on the black, and ≤ 0.01% retained on a 45 μm mesh for CP-CA80-PE.
  • Color: shades approved by spectrophotometer to Delta-E < 0.5, with lab plaques ready in 48 hours for custom color matches.
  • Lab: MFI, FPV, dispersion and spectrophotometry in-house, with every production lot screened before dispatch clearance; see quality control.
  • Documents: a one-page TDS per standard grade in the TDS library; MSDS, RoHS, REACH and food-contact declarations issued per grade on request.
  • Compliance: FDA 21 CFR 177.1520 on MB-W70-PE, MB-ADD-SAB and CP-CA80-PE, plus EU 10/2011 on MB-W70-PE and 178.3860 on MB-ADD-SAB; MB-W70-PE, MB-BLK40-AG and MB-ADD-SAB declared RoHS and REACH compliant, per the compliance matrix.
  • Supply: 10,000 MT installed annual extrusion capacity on high-torque co-rotating twin-screw lines, with 25 kg packing chosen per grade; see infrastructure.
  • Trials: trial lots follow plaque approval, the CP-CA80-PE TDS offers laboratory extrusion trials on request, and works visits can be arranged. Start at Request Sample.

To discuss a grade, call or WhatsApp +91 90544 82828, or email adcolindia@gmail.com.

FAQ

Choosing a masterbatch supplier, answered.

  • What should I ask a masterbatch supplier before ordering?

    Ask for the TDS and MSDS of the exact grade, the carrier and MFI with test conditions, the let-down ratio for your process, a dispersion result such as FPV, the Delta-E tolerance for colors, any food-contact or RoHS declarations you need, and a trial lot for your own line.

  • What is a good FPV value for masterbatch?

    It depends on pigment, loading and screen size, so compare results at the same mesh. As a reference, AdCol specifies FPV below 0.8 bar/g at 14 μm for its 70% rutile white MB-W70-PE and below 1.0 bar/g for its 40% carbon black MB-BLK40-AG, both to EN 13900-5.

  • Is the cheapest masterbatch per kg the cheapest option?

    Not always. Multiply the masterbatch price by the let-down ratio to get its cost per kg of finished product. A grade that needs 4% can cost more than a dearer one doing the same job at 2.5%, and poor dispersion adds hidden costs in screen changes and rejects.

  • How do I compare masterbatch suppliers fairly?

    Hold everything else constant: same resin, machine, gauge and target let-down ratio. Ask every supplier for the same tests to the same methods, run trial lots back to back, and compare cost per kg of finished product rather than list price.

  • Which documents should come with a masterbatch delivery?

    At minimum, a lot number on each bag and a certificate of analysis showing that lot's tested values against the TDS, plus an invoice naming the approved grade. Keep the TDS, MSDS and any food-contact or RoHS declarations on file, and ask for new versions when revised.

Samples & Trials

Have a line trial coming up? Let's match the grade to it.

Send your polymer, process and target let-down. Our lab confirms, tests and formulates the grade and dispatches a sample.